2-2 A-61500 April 2007 Making connections Follow the instructions for installing the IEEE-1394 (FireWire) card and the Kodak driver software before y
A-61500 April 2007 2-3Attaching the power cord The Kodak i600 Series Scanner is packed with a set of power cords. 1. Select the power cord which com
2-4 A-61500 April 2007 7 Stop/Pause and Start/Resume buttons — 8LEDs— illuminate or flash from top to bottom as follows:Illuminates when the power is
A-61500 April 2007 2-5Internal componentsSeparation roller — provides smooth document feeding of various sizes and textures one document at a time.I
2-6 A-61500 April 2007 Sensors — the scanner has 3 (ultrasonic) multi-feed detection sensors, 1 (optical) paper path sensor and 1 (optical) paper pre
A-61500 April 2007 3-1 3 Using the ScannerThis chapter provides the following operational procedures:• Turning on/off the scanner• Starting, stoppin
3-2 A-61500 April 2007Manually pausing and resuming the scannerWhile scanning documents:• Press the Stop/Pause button on the scanner once to pause sc
A-61500 April 2007 3-3Document preparationBefore you begin scanning documents, make certain the documents can be fed through the scanner easily.• A
3-4 A-61500 April 2007Maximum Document Size: 30.5 x 86 cm (12 x 34 in.). Documents larger than 43 cm (17 in.) require operator assistance.Paper inks:
A-61500 April 2007 3-5Locking the side guides Side guides may be locked into position after they are adjusted. This may be helpful when the placeme
A-61500 April 2007 iContents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Scan
3-6 A-61500 April 2007Adjusting the front of the output tray To raise the front of the output tray:1. Lift the front of the output tray.2. Swing the
A-61500 April 2007 3-7Adjusting the output tray for documents from 43 cm (17 in.) to 86 cm (34 in.)An output tray document extender is available for
3-8 A-61500 April 2007Adjusting the optional short document trayA short document tray is available for scanning smaller documents. This tray can be o
A-61500 April 2007 3-9Feeding documents using multi-feed detectionThe scanner has three multi-feed detection sensors. When Multi-feed detection is e
3-10 A-61500 April 2007Manual feeding To manually feed documents:1. Position the document you want to feed in the elevator tray so that the paper pre
A-61500 April 2007 3-11Calibrating the scannerThere are two types of calibration that can be performed on the i600 Series Scanners: Image calibratio
3-12 A-61500 April 2007The main Kodak Scanner window will be displayed.7. Click the Setup icon to access the main Kodak Scanner window.8. Click Setti
A-61500 April 2007 3-13The following screen will be displayed.10.Click Diagnostics. The following screen will be displayed.11. Click Calibrate. 12.S
3-14 A-61500 April 2007NOTE: If calibration fails, check the Operator Log for details. See Chapter 6, “Accessing the Operator Log” for more informati
A-61500 April 2007 4-14 The Enhanced PrinterThis chapter provides instructions for using the Enhanced Printer. The following information and procedure
ii A-61500 April 2007 Calibrating the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11Image calibration . .
4-2 A-61500 April 2007 Printer specificationsCharacteristic DescriptionMaximum lines 1 Maximum characters 40Print locations (horizontal) 12 front man
A-61500 April 2007 4-3Changing print positionsThe horizontal print position can be changed manually. Changing the front horizontal print position1. Re
4-4 A-61500 April 2007 3. The printer carrier slides easily along the rail. There is a small arrow on the green printer carrier. Slide the printer ca
A-61500 April 2007 4-5Replacing the ink cartridgeReplace the ink cartridge when:• printed characters appear light or uneven• missing characters are ev
4-6 A-61500 April 2007 6. Press and hold the release tab on the bottom of the printer carrier and rotate the printer carrier back into position.NOTE:
A-61500 April 2007 4-7Replacing the blotter stripsBlotter strips collect ink overflow. They should be replaced when there is a build-up of ink. Replac
4-8 A-61500 April 2007 6. Align the blotter strip in the transport channel. Be sure it is properly aligned before pressing the adhesive side into the
A-61500 April 2007 5-1 5 MaintenanceThis chapter provides:• a cleaning frequency chart• a list of cleaning tools and materials• a list of supplies a
5-2 A-61500 April 2007 Cleaning frequency chartA recommended cleaning sequence includes vacuuming the scanner transport, cleaning the residue from th
A-61500 April 2007 5-3Supplies and accessoriesContact your scanner supplier to order supplies. NOTE: Items and catalog numbers are subject to change
A-61500 April 2007 1-11 IntroductionThis User’s Guide provides information and procedures for the Kodak i600 Series Scanners. The information in thi
5-4 A-61500 April 2007 Cleaning procedure Follow the cleaning procedure below to ensure the best scanner performance and image quality.Cleaning the o
A-61500 April 2007 5-5Cleaning the drive rollers 5. Manually rotate and wipe the NFR and drive rollers with a roller cleaning pad.IMPORTANT: The ro
5-6 A-61500 April 2007 Cleaning the feed module tires11. Lift up the printer access cover.12.Push the release lever down (located underneath the prin
A-61500 April 2007 5-715.Reinstall the feed module by aligning the pins, fitting it into position and pulling up on the release lever to lock it int
5-8 A-61500 April 2007 Cleaning the scanner transport area17.Thoroughly vacuum the entire transport area, paying particular attention to these areas:
A-61500 April 2007 5-9Cleaning the background strips18.Using the green tabs pull off the upper and lower background strips and set them aside.19.Vac
5-10 A-61500 April 2007 23.Carefully vacuum the areas between the lamps (both upper and lower), then use a Staticide wipe to thoroughly clean the gla
A-61500 April 2007 5-11Running a transport cleaning sheet1. Place a transport cleaning sheet in the elevator tray in landscape orientation.2. Open t
5-12 A-61500 April 2007 Replacement proceduresThis section provides procedures for replacing the following parts. Use the list below as a guideline f
A-61500 April 2007 5-134. Push down on the release lever (located underneath the printer access cover) to release and remove the feed module.5. If y
1-2 A-61500 April 2007 Scanner models • Kodak i610 Scanner is a desktop duplex black and white and grayscale scanner with an automatic document feed
5-14 A-61500 April 2007 If you want to replace the tires, proceed as follows:6. With one hand, press the locking tabs (one on each side) while holdin
A-61500 April 2007 5-1512.Align the tabs on the upper housing with the slots on the lower housing.13.Press the upper and lower housings together unt
5-16 A-61500 April 2007 Replacing the separation roller or separation roller tires1. Open the pod.2. Pull the separation pad holder forward and remov
A-61500 April 2007 5-17Replacing the pre-separation padChange the pre-separation pad when the frequency of double-fed documents increases.1. Open th
A-61500 April 2007 6-16 TroubleshootingThis chapter provides:• A description of the indicator lights located on the front of the scanner.• Informati
6-2 A-61500 April 2007 Led display DescriptionScanner is in sleep mode and has detected a hardware error. Cycle power on the scanner. If the conditio
A-61500 April 2007 6-3Accessing the Operator LogThe Operator Log is accessed through the Scan Validation Tool.1. Select Start>Programs>Kodak&g
6-4 A-61500 April 2007 6. Click Settings. The following screen will be displayed.Click Device.The following screen will be displayed.
A-61500 April 2007 6-57. Click Diagnostics. The following screen will be displayed.8. Click the Logs tab. 9. From the drop down box, select Operator
6-6 A-61500 April 2007 Message listing Following is an alphabetic list of messages and corrective actions you can take if one of the following messag
A-61500 April 2007 1-3• Automatic and manual feeding.• JPEG compression allows color and grayscale images to be viewed in most image viewers.• Image
A-61500 April 2007 6-7Operator Log Message ID# Description/ActionImage buffer exceeded threshold 1, 48 The feeder has stopped and the transport is s
6-8 A-61500 April 2007 Operator Log Message ID# Description/ActionMulti-feed detected 23 A multi-feed document condition has been detected and the sc
A-61500 April 2007 6-9Operator Log Message ID# Description/ActionPrint head not installed 282 An attempt was made to use the Document Printer withou
6-10 A-61500 April 2007 Operator Log Message ID# Description/ActionUltrasonics calibration succeeded 332 Informational message. The scanner ultrasoni
A-61500 April 2007 6-11Numerical message listingUse the following numeric listing to quickly find an error. Use the previous Message Listing chart f
6-12 A-61500 April 2007 ID# Description/Action297 Elevator too full, feed module missing or broken301 Image size exceeds available memory306 Close po
A-61500 April 2007 6-13Problem solving Use the chart below as a guide to check possible solutions to problems you may encounter when using the Kodak
6-14 A-61500 April 2007 Problem Possible SolutionLong documents are not feeding or are jammingMake sure that:• the elevator tray extender is pulled o
A-61500 April 2007 A-1Appendix A AccessoriesThis chapter provides a description for the accessories that are available for use the Kodak i600 Series
A-61500 April 2007 B-1Appendix B SpecificationsScanner Type/Speed• i610 Scanner: duplex bi-tonal and grayscale scanner with an automatic document fe
1-4 A-61500 April 2007 Safety information Warning labelsMSDS Material Safety Data Sheets (MSDS) are available on the Kodak website at: www.kodak.com/
A-61500 April 2007 1-5EMC statementsUnited States This equipment has been tested and found to comply with the limits for a Class A digital device pu
A-61500 April 2007 2-12 Getting StartedSite specifications Place the scanner:• In a clean area with temperature and relative humidity typical of an
Komentáře k této Příručce